The Development of Agarwood Chopper Machines to Increase Agarwood Farmers' Efficiency During the Pandemic

Ahmad Mursyidun Nidhom, Gres Dyah Kusuma Ningrum, Azhar Ahmad Smaragdina

Abstract


Partner Village Development (PDM) State University of Malang is an activity that aims to develop regional superior potential to improve the economy of partner villages, develop science and technology and increase income generating for universities in the context of mass production of research and service products. One of the partner villages that needs to be developed is Mitra Senggreng Village, Sumber Pucung, Malang district which has the superior potential of agarwood which is very abundant. So far, agarwood is directly sold in an unprocessed condition, even though after processing the agarwood has a very high selling value. high, in this case the production of tasbih and perfume. Armed with the problems mentioned above, it is necessary to develop a Chopper Machine for Chopping Agarwood integrated with the Smart Gaharu application to make it easier for partner village communities to process agarwood into tasbih and perfume. which focuses on developing the potential of Agarwood wood and becomes a pioneer for future development. In general, the development of this gaharu chopper machine went through 5 stages of the implementation method process, which started from 1) preparation, 2) making the chopper machine, 3) socialization, 4) evaluation, and 5) reporting. The result of this service activity is the development of a Chopper Machine that can effectively be used by gaharu farmers to chop agarwood quickly and easily, the average effectiveness results of 81% obtained from an open questionnaire distributed by farmers through a trial mechanism of 82%, and test results agarwood products by 80%.


Full Text:

PDF

References


Andasuryani., Santosa., Chandra, Alhapen Ruslin. 2009. Membangun Mesin Pencacah Rumput Gajah Untuk Peningkatan Efektivitas Konsumsi Pakan Ternak Sapi. Artikel Ilmiah Pelaksanaan Program Pengabdian Program Vucer Tahun 2009

Aji, Dhanar Yuwono. 2013. Desain Generator Axial Kecepatan Rendah Dengan Menggunakan Magnet Permanen. Skripsi,. Surakarta: Universitas Muhammadiyah Surakarta

Azwin, Rahmat.2013, Reverse Engineering dan Re-Engineering sebagai solusi pemeliharan pembangkit.Info PJB, Eisi 84/November. Hal 3-5

Bagci, E., 2009, Reverse Engineering Aplications for Recovery of Broken or Worn Parts and Re-Manufacturing: three Case Studies, Journal of Advances in Engineering Software. Vol. 40 Issue 6, pp. 407-418.

Batubara ,Helmina. 2013. Penentuan Harga Pokok Produksi Berdasarkan Metode Full Costing Padanpembuatan Etalase Kaca Dan Alumunium Di Ud. Istana Alumunium Manado. Jurnal Emba. Vol.1 No.3 September 2013, Hal. 217- 224

Bimo ,Ardi Bawono., Santoso, Hari., dan Soemarwanto. 2007. Rancang Bangun Automatic Transfer Switch Pada Motor Bensin Generator-Set 1 Fasa 2,8 Kw 220 Volt 50 Hertz. Jurnal Eeccis Vol. 1, No. 1, Juni 2007

Burston, M.T., Sabatini, R., Clothier, R., Gardi, A., dan Ramasamy, S. 2014. “Reverse Engineering of a Fixed Wing Unmanned Aircraft 6-DoF Model for Navigation and Guidance Applications”, Applied Mechanics and Materials, vol. 629, pp. 164-169, Trans Tech Publications, 2014. DOI: 10.4028/www.scientific.net/AMM.629.164

Corbo, p., Germani M., Mandorli F. 2004, Aesthetic And Functinal Analysis for Product Model Validation in Reverse Engineering Aplication, Computer Aided Design, 36, pp 65-74.

DITJENAK., 2006. Kebutuhan Susu DiIndonesia,Impor Susu Untuk Memenuhi Kebutuhan Susu Indonesia.

Febriantoko, Bambang Waluyo. 2012.Reverse Engineering Sebagai Basis Desain Pengenmbangan Mobil Mini Truck Esemka. Prosiding Semminar Nasional Aplikasi Sains & Teknilogi (SNAST) periode III. Yogyakarta: 3 November 2012

Kumar A., Jain, P. K. & Pathak, P. M. 2013. Reverse Engineering In Product Manufacturing: An Overview. Dalam International Scientific Book 2013 Pp. 665-678 Chapter 39

Lasena , Sitty Rahmi. 2013. Analisis Penentuan Harga Pokok Produksi Pada Pt. Dimembe Nyiur Agripro. Jurnal Emba 585.Vol.1 No.3 Juni 2013, Hal. 585- 592

Panchhetti M., Pernot J.P., Veron P.,2010, Towards Recovery of Complex Sapes in Meshes Using Digital Images for Reverse Engineering Aplication, Cumputer Aided Design, 42, pp 693-707

Raja, V. 2008. Reverse Engineering, Springer Verlag London.

Shanghai MAC Company. 2013. Jenis – enis Mesin Pencacah Rumput Ternak Sapi. Diakses Pada Tanggal 31 Mei 2016 Didapatkan dari http://www.idpenghancur.com/mill/n_4300.html

Slat, Andre Henri. 2013. Analisis Harga Pokok Produk Dengan Metode Full Costing Dan Penentuan Harga Jual. Jurnal Emba. Vol.1 No.3 Juni 2013, Hal. 110-117

Sulistyono. 2015. Perancangan Desain Gitar Elektrik Senar 8 (Ts-8) Dengan Kombinasi Perangkat Smartphone Sebagai Virtual Efek Gitar Menggunakan Metode Reverse Engineering. Skripsi,. Surakarta: Universitas Muhammadiyah Surakarta.


Refbacks

  • There are currently no refbacks.